产品系统NEWS CENTER

在发展中求生存,不断完善,以良好信誉和科学的管理促进企业迅速发展
产品系统

首页-产品系统-体积表面电阻率测试仪-高绝缘电阻率测试仪-LST-122薄膜电阻测试仪

薄膜电阻测试仪

更新时间:2024-01-12

简要描述:薄膜电阻测试仪测量高电阻,又可测微电流。采用了美国In公司的大规模集成电路,使仪器体积小、重量轻准确度高。数字液晶直接显示电阻值和电流。量限从1×104Ω ~1×1018 Ω,是目前国内测量范围Z宽,准确度Z高的数字超高阻测量仪。电流测量范围为2×10-4 ~1×10-16A。机内测试电压10V/50V/100V/250V/500V/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、

  • 厂家实力

    Manufacturer Strength
  • 有效保修

    Valid Warranty
  • 质量保障

    Quality Assurance

详细介绍

薄膜电阻测试仪 一  概述 

本仪器既可测量超高电阻,又可测极微弱电流。采用了大规模集成电路以及的技 术,使仪器体积小、重量轻、准确度高。以数字液晶显示电阻并同时直接显示流过被测电阻的电流。电阻量程从1×104Ω ~1×1018Ω, 电流测量范围 为2 ×10-4A ~1 ×10-16A。机内测试电压为DC10V、50V、100V、250V、500V、1000V。

本仪器具有精度高、显示迅速、稳定性好、读数方便, 适用于防静电产品 如防静电鞋、防静电塑料橡胶制品、计算机房防静电活动地板等电阻值的检验以及绝缘材料和电子电器产品的绝缘电阻测量。本仪器除能测电阻外,还能直接测量电流如电子器件暗电流等。

二  主要特点 


  电阻测量范围 1×104Ω ~1×1018 Ω; 

  电流测量范围 2×10-4A ~1×10-16A; 

  体积小、重量轻、准确度高;

  *的被测电阻、和流过电阻的电流双显示,使操作测量更加方便;

          性能稳定、读数方便;

          既能测电阻又能测电流;

  测试电压有六种选择DC10V、50V、100V、250V、500V、1000V;

         使用操作简便,在任何电阻量程和测试电压下均直接读显示数字结果,免去要乘以一个系数的麻烦,使测量超高电阻就如用万用表测量普通电阻样简便。

三  主要应用范围 


材料高阻测试测量如防静电产品(防静电鞋、防静电塑料橡胶制品、计算机房防静电活动地板等)电阻值的检测;

材料体电阻(率)和表面电阻(率)测量;

电化学和材料测试,以及物理,光学和材料研究;

微弱电流测量如光电效应和器件暗电流测量。

      

四  技术指标 

1.   电阻测量范围: 1×104Ω ~1×1018Ω,分为十个量程。

2.   电流测量范围为2×10-4A ~1×10-16A

3.   全数字液晶屏显示。

4.   准确度: 准确度优于下表


量程

有效显示范围

20~30℃ RH<80%

104

0.01~19.99

1%

105

0.01~19.99

1%

106

0.01~19.99

1%

107

0.01~19.99

1%

108

0.01~19.99

1%

109

0.01~19.99

1%

1010

0.01~19.99

5%+2

1011

0.01~19.99

5%+2

1012

0.01~19.99

5%+5

1013

0.01~19.99

10%+5

1014

0.01~19.99

10%+5

1014以上

0.01~19.99

10-15%+5

( 超出有效显示范围时误差有可能增加)测试电流准确度与电阻相同


测试电压准确度为 10%

5. 使用环境: 温度 -10℃~50℃ 相对湿度<90%。

6. 测试电压: DC10V、50V、100V、250V、500V、1000V。±10%

7. 供电形式: AC 220V,50HZ,功耗约10W。

8. 仪器尺寸: 300mm× 280mm× 150 mm。

9. 重量: 约3.0KG。


 五  工作原理  

        根据欧姆定律,被测电阻R等于施加电压V除以通过的电流I。即   


   V

R= ---

   I


        传统的仪器的工作原理是测量电压V固定,通过测量流过被测物体的电流I以标定电阻的刻度来读出电阻值。从上式可以看出,由于电流I是与电阻成反比,而不是成正比,所以电阻的显示值是非线性的,即电阻无穷大时,电流为零,即表头的零位处是∞,其附近的刻度非常密,分辨率很低。整个刻度是非线性的。又由于测量不同的电阻时,其电压V也会有些变化,所以普通的高阻计的精度是很难提高的。 

       ZST-121体积、表面电阻率测定仪是同时测出电阻两端的电压V和流过电阻的电流I,通过内部的大规模集成电路完成电压除以电流的计算,然后把所得到的结果经过A/D转换后以数字显示出电阻值,即便是电阻两端的电压V和流过电阻的电流I是同时变化,其显示的电阻值不象普通高阻计那样因被测电压V的变化或电流I的变化而变,所以, 即使测量电压、被测量电阻、电源电压等发生变化对其结果影响不大,其测量精度很高。从理论上讲其误差可以做到零。而实际误差可以做到千分之几或万分之几。 


 六  使用方法 

6.1接好电源线 

确保电源为220VAC/50Hz 

6.2接通电源 

    将电流电阻量程置于 104 档,电压量程置于10V,然后开机。

6.3调零 

在“Rx"两端开路的情况下,调零使电流表的显示为0000 .注意:在“Rx"两端不开路,如接在电阻箱或被测量物体上时调零后测量会产生很大的误差。一般一次调零后在测试过程中不需再调零。 完毕后关机。

6.4连接线路 

     接好测试线,将测试线将主机与屏蔽箱连接好,测体积电阻时测试按钮拨到Rv边,测表面电阻时测试按钮拨到Rs边。然后开机。

6.5选择合适的测量电压 

电压选择开关在后面板,注意,在测试过程中不要随意改动测量电压,可能因电压的过高或电流过大损坏被测试器件或测试仪器; 

6.6测试 

测量时从低档位逐渐拔往高档,每拨一次稍停留1~2秒以使观察显示数字, 当被测电阻大于仪器测量量程时,电阻表显示“1",此时应继续将仪器拨到量程更高的位置,当测量仪器有显示值时应停下,当前的数字乘以档次即是被测电阻值。当有显示数字时不要再往更高次档拨,否测仪器会过量程,机内保护电路开始工作,仪器测量准确度会下降。 

6.7 测试完毕将电阻电流量程拔至“104 "档,电压量程调至10V后关闭电源

每测量一次均应将量程开关拨回到104“调零"档的量程位置以免开机或测量端短路时而损坏仪器。

6.8 测量电流及1015Ω以上超高电阻的测量应用测量电流后用欧姆定律以电压除以电流计算电阻的方法,详见8.5节内容。

6.9 体积电阻和表面电阻转换

在测试过程中,使用屏蔽箱在进行体积电阻和表面电阻转换时,必须把电源关闭后进行档位转换,否则会导致电压冲击到主机无法显示或损坏。


薄膜电阻测试仪 七  使用注意事项 

★高阻测量一定要严格按使用方法步聚进行,否则有可能造成仪器*损坏或电人。 

7.1 应在“Rx"两端开路时调零(主机开机)

如接在电阻箱或被测量物体上时调零后测量会产生很大的误差。一般一次调零后在测试过程中不需再调零,但改变测量电压后可能要重新调零。 

7.2 禁止将“Rx"两端短路,以免微电流放大器受大电流冲击

7.3 在测试过程中不要随意改动测量电压, 

随意改动测量电压可能因电压的过高或电流过大损坏被测试器件或测试仪器,而且有的材料是非线性的,即电压与电流是不符合欧姆定律,有改变电压时由于电流不是线性变化,所以测量的电阻也会变化。 

7.4 测量时从低次档逐渐拔往高次档 

每拨一次稍停留1~2秒以便观察显示数字,当有显示值时应停下,记录当前的数字即是被测电阻值。若显示“1"时,表示欠量程应往高次档拔。直到有显示数字时为止。当有显示数字时不能再往高次档拨,否则有可能损坏仪器(机内有过电流保护电路)。除104 Ω档之外,当显示低于1.99,表示过量程应换低档! 

7.5 大部分绝缘材料,特别是防静电材料的电阻值在加电压后会有一定变化而引起数字变化 

由于本仪器的分辩率很高,因而会引起显示值的末尾几位数也变化,这不是仪器本身的问题,而是被测量对象的导电机理复杂而使得阻值有些变化。在这种情况下往往取2位有效数就够了。 

7.6 接通电源后,手指不能触及高压线的金属部分 

★本仪表有二连根线:高压线(红)和微电流测试线。在使用时要注意高压线,开机后人不能触及高压线,以免电人或麻手。 

7.7 测试过程中不能触摸微电流测试端 

微电流测试端zui怕受到大电流或人体感应电压及静电的冲击。所以在开机后和测试过程中不能与微电流测试端接触,以免损坏仪表。 

7.8 在测量高阻时,应采用屏蔽盒将被测物体屏蔽. 

在测量大于1010 Ω以上时,为防止外界干扰面而引起读数不稳。 

7.9 每次测量完时应将量程开关拨回“104 "档再进行下次测试

在测量时应逐渐将量程开关拨到高阻档,测量完时应将电流电阻量程、电压量程开关拨回低档。以 确保下次开机时量程开关处在低阻量程档。


An overview

本仪器既可测量超高电阻,又可测极微弱电流。采用了大规模集成电路以及的技 术,使仪器体积小、重量轻、准确度高。以数字液晶显示电阻并同时直接显示流过被测电阻的电流。电阻量程从1×104Ω ~1×1018Ω, 电流测量范围 为2 ×10-4A ~1 ×10-16A。机内测试电压为DC10V、50V、100V、250V、500V、1000V。

This instrument can measure high resistance, and can measure weak current. The large scale integrated circuit and new patent technology, the instrument has the advantages of small volume, light weight, high accuracy. In a digital liquid crystal display resistance and directly display the current flowing through the measured resistance. Resistance range from 1 × 104 to 1 × 1018 Ω, current measuring range is 2 × 10-4A ~ 1 × 10-16A. The built-in test voltage of DC10V, 50V, 100V, 250V, 500V, 1000V.

本仪器具有精度高、显示迅速、稳定性好、读数方便, 适用于防静电产品 如防静电鞋、防静电塑料橡胶制品、计算机房防静电活动地板等电阻值的检验以及绝缘材料和电子电器产品的绝缘电阻测量。本仪器除能测电阻外,还能直接测量电流如电子器件暗电流等。

The instrument has high precision, good stability, shows a rapid, convenient reading, suitable for measuring insulation resistance in anti-static products such as anti-static shoes, anti-static plastic and rubber products, computer room anti electrostatic floor activities such as inspection resistance and insulation materials and electronic products. This instrument can measure resistance, current electronic device can directly measure such as dark current.

二 主要特点

Two main features

电阻测量范围 1×104Ω ~1×1018 Ω;

Resistance measurement range of 1 × 104 to 1 × 1018 Ω;

电流测量范围 2×10-4A ~1×10-16A;

The current measurement range of 2 × 10-4A ~ 1 × 10-16A;

体积小、重量轻、准确度高;

Small volume, light weight, high accuracy;

*的被测电阻、和流过电阻的电流双显示,使操作测量更加方便;

Current, resistance, and resistance is measured through the unique dual display, make the operation more convenient;

性能稳定、读数方便;

Stable performance, easy reading;

既能测电阻又能测电流;

Not only can measure resistance and the measured current;

测试电压有六种选择DC10V、50V、100V、250V、500V、1000V;

The test voltage is six DC10V, 50V, 100V, 250V, 500V, 1000V;

使用操作简便,在任何电阻量程和测试电压下均直接读显示数字结果,免去要乘以一个系数的麻烦,使测量超高电阻就如用万用表测量普通电阻样简便。

The operation is convenient, in any resistance range and test voltage are directly read and display digital results, so it is multiplied by a coefficient of trouble, ultra high resistance as measured with a multimeter common resistance is measured.

三 主要应用范围

The three main applications

材料高阻测试测量如防静电产品(防静电鞋、防静电塑料橡胶制品、计算机房防静电活动地板等)电阻值的检测;

The measurement of high resistance testing materials such as anti-static products (anti-static shoes, anti-static plastic and rubber products, computer room activities of anti-static flooring etc.) detection resistance value;

材料体电阻(率)和表面电阻(率)测量;

Material body resistance (rate) and surface resistance (rate) measurement;

电化学和材料测试,以及物理,光学和材料研究;

The electrochemical and material testing, as well as physical, optical and material research;

微弱电流测量如光电效应和器件暗电流测量。

Weak current measurement as photoelectric effect and dark current measurement device.

四 技术指标

The four technical indicators

1. 电阻测量范围: 1×104Ω ~1×1018Ω,分为十个量程。

1 resistance measurement range: 1 × 104 ~ 1 × 1018 Ω, divided into ten ranges.

2. 电流测量范围为2×10-4A ~1×10-16A

2 current measuring range is 2 × 10-4A ~ 1 × 10-16A

3. 全数字液晶屏显示。

3 all digital LCD display.

4. 准确度: 准确度优于下表

4 accuracy: the accuracy of the table below

量程 有效显示范围 20~30℃ RH<80%

The range of effective display area of 20 ~ 30 ℃ RH<80%

104 0.01~19.99 1%

104 0.01~19.99 1%

105 0.01~19.99 1%

1050.01 19.991%

106 0.01~19.99 1%

1060.01 19.991%

107 0.01~19.99 1%

1070.01 19.991%

108 0.01~19.99 1%

1080.01 19.991%

109 0.01~19.99 1%

1090.01 19.991%

1010 0.01~19.99 5%+2字

10100.01 ~ 19.99 5%+2 words

1011 0.01~19.99 5%+2字

10110.01 ~ 19.99 5%+2 words

1012 0.01~19.99 5%+5字

10120.01 ~ 19.99 5%+5 words

1013 0.01~19.99 10%+5字

10130.01 ~ 19.99 10%+5 words

1014 0.01~19.99 10%+5字

10140.01 ~ 19.99 10%+5 words

1014以上 0.01~19.99 10-15%+5字

More than 1014 of 0.01 ~ 19.99 10-15%+5 words

( 超出有效显示范围时误差有可能增加)测试电流准确度与电阻相同

(beyond the effective display range error may increase) test current accuracy and the same resistance

测试电压准确度为 10%

The test voltage accuracy is 10%

5. 使用环境: 温度 -10℃~50℃ 相对湿度<90%。

5 the use of the environment: temperature of -10 ℃ ~ 50 ℃ relative humidity <90%.

6. 测试电压: DC10V、50V、100V、250V、500V、1000V。±10%

6 the test voltage: DC10V, 50V, 100V, 250V, 500V, 1000V. ± 10%

7. 供电形式: AC 220V,50HZ,功耗约10W。

7 power supply forms: AC 220V, 50HZ, power consumption is about 10W.

8. 仪器尺寸: 300mm× 280mm× 150 mm。

The 8 instrument size: 300mm x 280mm x 150 mm.

9. 质量: 约3.0KG。

9 quality: about 3.0KG.

五 工作原理

The five principle

根据欧姆定律,被测电阻R等于施加电压V除以通过的电流I。即

According to Ohm's law, the measured resistance R is equal to the applied voltage divided by current V by I. That is

V

V

R= ---

R= -

I

I

传统的仪器的工作原理是测量电压V固定,通过测量流过被测物体的电流I以标定电阻的刻度来读出电阻值。从上式可以看出,由于电流I是与电阻成反比,而不是成正比,所以电阻的显示值是非线性的,即电阻无穷大时,电流为零,即表头的零位处是∞,其附近的刻度非常密,分辨率很低。整个刻度是非线性的。又由于测量不同的电阻时,其电压V也会有些变化,所以普通的高阻计的精度是很难提高的。

The working principle of traditional instrument is to measure the voltage of V fixed, scale current by measuring the flow through the measured object I to calibrate the resistance to read the value of resistance. Can be seen from the above equation, the current I is inversely proportional to the resistance, not proportional, so is nonlinear resistive display value, namely the infinite resistance, current is zero, i.e. zero at the header is ∞, graduated in the vicinity of the very tight, very low resolution. The scale is nonlinear. Because the resistance measurement is different, its voltage V there will be some changes, so the high resistance of ordinary meter accuracy is difficult to improve.

ZST-121体积、表面电阻率测定仪是同时测出电阻两端的电压V和流过电阻的电流I,通过内部的大规模集成电路完成电压除以电流的计算,然后把所得到的结果经过A/D转换后以数字显示出电阻值,即便是电阻两端的电压V和流过电阻的电流I是同时变化,其显示的电阻值不象普通高阻计那样因被测电压V的变化或电流I的变化而变,所以, 即使测量电压、被测量电阻、电源电压等发生变化对其结果影响不大,其测量精度很高。从理论上讲其误差可以做到零。而实际误差可以做到千分之几或万分之几。

ZST-121 volume, surface resistivity tester is current and voltage V and flow resistance at the same time measuring resistor I, the large scale integrated circuit internal to complete the calculation of voltage divided by current, and then the obtained results after A/D conversion to digital display resistance value, even if is current and voltage of V and flow resistance at both ends of the I is changed at the same time, it shows the value of resistance do not like ordinary high resistance meter that due to changes in the measured voltage or current change of V I and change, so, even if the measurement of voltage, resistance, power supply voltage is measured changes had little effect on the results, the measuring accuracy is very high. Theoretically the error can do zero. But the actual error can be done a few thousandths or very few.

六 使用方法

Six using the method

6.1接好电源线

6.1 connect the power line

确保电源为220VAC/50Hz

Ensure that the power supply is 220VAC/50Hz

6.2接通电源

6.2 connect the power supply

将电流电阻量程置于 104 档,电压量程置于10V,然后开机。

The current resistance range in 104 gear, voltage range on the 10V, and then boot.

6.3调零

6.3 zero

在“Rx"两端开路的情况下,调零使电流表的显示为0000 .注意:在“Rx"两端不开路,如接在电阻箱或被测量物体上时调零后测量会产生很大的误差。一般一次调零后在测试过程中不需再调零。 完毕后关机。

In the "Rx" both ends open circuit case, zero to display the current meter is 0 note: do not open the "Rx" ends, such as the resistance box or the object being measured at zero measurement will produce great error. A general tone in the testing process need not be zero zero. After shutdown.

6.4连接线路

6.4 connecting line

接好测试线,将测试线将主机与屏蔽箱连接好,测体积电阻时测试按钮拨到Rv边,测表面电阻时测试按钮拨到Rs边。然后开机。

Connect the test line, test line will host and shielding box is connected well, the test button to dial Rv boundary to measure the volume resistance, surface resistance test button to dial Rs. And then boot.

6.5选择合适的测量电压

6.5 select the appropriate measuring voltage

★电压选择开关在后面板,注意,在测试过程中不要随意改动测量电压,可能因电压的过高或电流过大损坏被测试器件或测试仪器;

★ voltage selection switch on the rear panel, pay attention to, in the process of testing do not arbitrarily change the measured voltage, probably due to voltage is too high or too large current and damage to the device or instrument test;

6.6测试

The 6.6 test

测量时从低档位逐渐拔往高档,每拨一次稍停留1~2秒以使观察显示数字, 当被测电阻大于仪器测量量程时,电阻表显示

When measured from low-grade to high-grade gradually pulled out, each dial again slightly for 1 ~ 2 seconds to make the observation of figures, when the measured resistance is greater than the measurement range, resistance meter display


产品咨询

留言框

  • 产品:

  • 您的单位:

  • 您的姓名:

  • 联系电话:

  • 常用邮箱:

  • 省份:

  • 详细地址:

  • 补充说明:

  • 验证码:

    请输入计算结果(填写阿拉伯数字),如:三加四=7

相关产品

关注我们
微信账号

扫一扫
手机浏览

Copyright©2024  北京航天易达仪器设备有限公司  版权所有    备案号:京ICP备2022030362号-1    sitemap.xml    技术支持:化工仪器网    管理登陆